[2.13.0]

Added: Now, initialization data is saved. This speeds up initialization and allows you to start with any posture during initialization.

Initialization data is automatically created for new components. For previously created components, it is automatically created by entering prefab mode or placing them in the scene.

The status of the initialization data is displayed in the information field of the Inspector.

Improvement: Changed runtime construction to start construction 5ms after initialization. This is to distribute the load when performing a large amount of instantiation or initialization at once.

Improvement: Added execution environment such as OS and CPU to the ManagerInformation log.

Fixed: If a registered root bone or renderer is duplicated, an error will occur and the system will not work.

Fixed: Fixed an issue where the anchor reference object was not properly cleared when the team was destroyed.

Fixed: Fixed an issue where some processes in runtime construction were not burst compiled. This improved the construction speed.

Fixed: Fixed the custom normal calculation algorithm. Normals now point in a more correct direction.

Fixed: Fixed an issue where the normal adjustment of the front hair of the sample UnityChanKAGURA was incorrectly set.

[2.12.0]

Added: Added a check to monitor the PlayerLoop in MagicaSettings, which resets the PlayerLoop if it gets overwritten by an external asset.

Improvement: Significantly speeds up system-related processing performed in C#.

Improvement: Disabled the initial state of distance culling.

Improvement: Changed the initial value of inertia smoothing to 0.4 and the initial value of tether compression to 0.4. This is an improvement to make the behavior better.

Improvement: Adjusted the values of inertia smoothing and tether compression for each preset.

[2.11.1]

Fixed: Fixed an issue where switching simulation frequency during execution could cause inconsistencies in time management, leading to mesh loss in some cases.

Fixed: Improved the display prediction algorithm, which significantly improved the issue of meshes stretching more than necessary when lag occurred.

Fixed: Fixed various issues that occurred when synchronizing two meshes with different scales when using self-collision.

[2.11.0]

Added: Recalculation mode for tangents has been added to MeshCloth.

Improvement: All components can now be multi-selected and multi-edited.

Improvement: Gizmo now displays correctly during multi-selection.

Improvement: Editor's gizmo toggle has been improved to allow enabling/disabling gizmo display for each component.

Fixed: Fixed an issue where scale 0 would cause an error. However, the simulation results will not be displayed when the scale is 0.

[2.10.0]

Added: Added distance culling. Simulation will stop if the distance is greater than the set distance. This improves performance.

Added: Added a way to specify vertex attributes as an attribute array corresponding to the mesh's vertex array when constructing MeshCloth at runtime. This is an alternative to using paint maps as attributes.

Improved: Changed the blendWeight, which was previously an unexposed property, to be able to be manipulated from the Inspector.

Improved: Changed so that the Transform posture is returned to its initial state when BoneCloth/BoneSpring is disabled.

Fixed: Fixed an issue where SetWindDirection(), the WindZone wind direction change function, was not working properly.

[2.9.1]

Fixed: Non-uniform scaling is now a warning rather than an error, but is still not recommended and can cause various problems.

[2.9.0]

Added: Added a ReverseDirection flag to Capsule Collider. You can reverse the direction of the capsule.

Added: The blendWeight parameter can now be animated.

Improved: Component scale state is now verified. Anything other than uniform scale will result in an error.

Improved: Some changes have been made to custom skinning. This is to improve usability.

Fixed: Fixed an issue where vertices would continue to bounce in the collision detection between edges and capsule colliders depending on the situation.

Fixed: Fixed an issue where the initial direction of gravity was not recorded correctly when using pre-built objects. This resolves the issue where GravityFalloff would not work when using pre-built objects. However, to fix this, you will need to recreate the pre-built data.

[2.8.0]

Added: Negative scale is now supported. Negative scale can be set for only one axis, XYZ.

Improvement: Some presets were readjusted.

Improvement: The push direction of the plain collider is now displayed.

Fixed: Fixed a problem that the collider works even if it is disabled from the beginning.

[2.7.0]

Added: Added inertia smoothing function. It is possible to reduce the disturbance of the cloth due to sudden movement. It can be adjusted with the "World Inertia Smoothing" parameter in the inertia panel.

Added: Added AnimatorLinkage to UpdateMode. Automatically sets the appropriate update mode in conjunction with the character's Animator.

Fixed: Fixed an issue where assert logs were displayed when a component was destroyed during runtime build initialization. Note that this assertion has no effect on operation.

Improvement: Adjusted the inertial smoothing parameters of UnityChanKAGURA.

Improvement: Adjusted inertial smoothing parameters for each preset.

Improvement: Changed UpdateMode of sample UnityChanKAGURA to AnimatorLinkage.

[2.6.1]

Fixed: When using the culling function with Animator's CullMode set to "Cull Update Transforms", we fixed an issue where the simulation would not restart once it was removed from the camera.

...

https://magicasoft.jp/en/mc2_releasenote/

Magica Cloth 2