[2.16.4]

Fixed: When using mutual self-collision collisions, an issue where an infinite loop could occur and the application would freeze under certain circumstances has been fixed. This issue was confirmed in MetaQuest.

Fixed: When using Edge mode collision detection, an issue where friction on some particles would not be released and their movement would become sluggish has been fixed. This issue has existed since the initial release.

[2.16.3]

Improvement: Now compatible with Unity 6.3.

Fixed: Fixed an issue where, in certain circumstances, friction would remain even after contact with the collider was released, causing unstable behavior.

[2.16.2]

Important Note: The minimum version of the Unity Editor that can be used has been raised from Unity 2021.3.16 to Unity 2021.3.20.

Improvement: Fixed all warnings in Microsoft.Unity.Analyzers. This is an improvement to code correctness and type safety, and does not change behavior.

Fixed: Fixed an issue in MeshCloth where normal calculations could be inaccurate if the scale of the MagicaCloth component and the renderer were different.

Fixed: Fixed an issue where particles would get jittery after teleporting when using Keep Teleport in combination with World Inertia Smoothing.

[2.16.1]

Fixed: Fixed a critical issue that could cause a crash in some circumstances when using self-collision.

Fixed: Fixed to properly free memory when closing a built application.

Fixed: Fixed an issue where a rare error would occur due to the order of initialization when running in the editor environment.

Fixed: Fixed an issue where setting a collider to 0 or a very small scale could cause a NaN error, and in some cases a crash.

[2.16.0]

Added: Now supports Unity 6.1.

Added: Added a demo scene specifically for Unity 6.1. Please note that this demo scene is the only one that will work with Unity 6.1 or later.

Fixed: Fixed an issue where a warning message would appear when using Transform in Unity 6.

[2.15.1]

Added: You can now change the UV number to read when specifying MeshCloth vertex attributes with a paint map.

Improvement: Improved validation of initialization data. If a problem is found with the initialization data, the system will switch to a full runtime build.

Fixed: Fixed an issue that caused drawing to be distorted when running BoneCloth in UnityPhysics(FixedUpdate) update mode and manipulating BlendWeight.

[2.15.0]

Added: Added a symmetry setting to colliders. You can easily set left and right colliders for arms, legs, etc.

Added: Added GetUseTransform() to the MagicaCloth component API.

Improvement: Improved to stop all unnecessary processing if there are zero running MagicaCloth components.

Improvement: Changed some of the colliders in the UnityChanKAGURA and Kohaku samples to symmetric colliders.

Fixed: Fixed an issue where the collider center offset was not working properly when using negative scale.

[2.14.3]

Fixed: Fixed an issue where adjusting the Sphere Collider and Capsule Collider sliders would not have any effect when the Editor was running.

[2.14.2]

Fixed: Fixed an issue where enabling self-collision on BoneCloth with no triangle information would cause an error.

[2.14.1]

Fixed: Fixed an issue where Transform posture was broken when running BoneCloth/BoneSpring in a split job.

Fixed: Fixed an issue where split jobs would continue to be applied even after self-collision and mutual collision were removed.

[2.14.0]

Improvement: Simulation jobs have been optimized. This has improved processing speed by 20% to 50%.

Improvement: If the number of vertices in a proxy mesh is less than 300, it is now processed in one job. This improves processing speed.

Improvement: If the number of vertices in a proxy mesh is 300 or more, or if self-collision is used, the job is now appropriately divided according to the number of available worker threads.

Improvement: The memory usage required for simulation has been reduced.

Improvement: Self-collision is now in Beta2. The processing has been optimized and the algorithm has been improved. Therefore, the behavior may be different from before.

Added: The number of vertices of a proxy mesh that will be the boundary for job division can now be set in MagicaSettings.

Added: An API has been added to set the number of vertices of a proxy mesh that will be the boundary for job division.

Added: An API to get MeshCloth's original mesh and custom mesh has been added to MagicaClothAPI.cs.

Added: Added an argument to the OnBuildComplete event.

[2.13.2]

Fix: Fixed an issue where using AngleRestoration/AngleLimit in certain circumstances could result in missing meshes and possibly crashing the app.

...

https://magicasoft.jp/en/mc2_releasenote/

Magica Cloth 2